Wear Characteristics of Aluminium-Graphite Composites Produced by Stir Casting Technique

Autori

  • S. C. Patnaik Department of Metallurgical and Materials Engineering, Indira Gandhi Institute of Technology, Sarang, Dhenkanal, Odisha, India
  • P. K. Swain Department of Chemistry, Indira Gandhi Institute of Technology, Sarang, Dhenkanal, Odisha, India
  • P. K. Mallik Department of Metallurgical and Materials Engineering, Indira Gandhi Institute of Technology, Sarang, Dhenkanal, Odisha, India
  • S. K. Sahoo Department of Metallurgical and Materials Engineering, Indira Gandhi Institute of Technology, Sarang, Dhenkanal, Odisha, India

Parole chiave:

Particulate composites, wear resistance, lubrication, stir casting

Abstract

Metal matrix composites (MMCs) are finding more applications due to their significantly improved properties such as high specific strength, high specific modulus, good damping capacity and good wear resistance compared to unreinforced alloys. In recent years, there has been an increasing interest in composites containing low density and low cost reinforcements. Graphite is one of the most suitable and low density reinforcement available for making light-weight and wear resistant parts for aircraft and automobile industry. At present the particulate reinforced aluminium matrix composites are gaining importance because of their low cost with advantages like isotropic properties and ease of fabrication. Use of aluminum as an antifriction material has been limited because of unfavorable wear. To improve wear resistance, it has been proposed to disperse graphite particles in to Al matrix. The present investigation is an attempt to produce particulate Al-graphite composites with superior wear resistance. Al-graphite composites with 1wt%, 3wt% and 5wt% graphite were prepared by stir casting technique by addition of graphite particles into the Al-melt treated with magnesium. Wear, hardness, and coefficient of friction studies of the composites were carried out. Graphite addition was found to increase wear resistance and the composite with 1wt% graphite had maximum hardness.Keywords: Particulate composites, wear resistance, lubrication, stir casting

Biografie autore

  • S. C. Patnaik, Department of Metallurgical and Materials Engineering, Indira Gandhi Institute of Technology, Sarang, Dhenkanal, Odisha, India
    Lecturer, Department of Chemistry
  • P. K. Swain, Department of Chemistry, Indira Gandhi Institute of Technology, Sarang, Dhenkanal, Odisha, India
    Professor, Department of Metallurgical and Materials Engineering
  • P. K. Mallik, Department of Metallurgical and Materials Engineering, Indira Gandhi Institute of Technology, Sarang, Dhenkanal, Odisha, India
    Assistant Professor, Department of Metallurgical and Materials Engineering.
  • S. K. Sahoo, Department of Metallurgical and Materials Engineering, Indira Gandhi Institute of Technology, Sarang, Dhenkanal, Odisha, India
    Lecturer, Department of Metallurgical and Materials Engineering.

Dowloads

Pubblicato

2014-11-26

Fascicolo

V. 4 N. 3 (2014)

Sezione

Research Articles

Licenza

Declaration and Copyright Transfer Form

(to be completed by authors)

 

I/ We, the undersigned author(s) of the submitted manuscript, hereby declare, that the above manuscript which is submitted for publication in the STM Journals(s), is not published already in part or whole (except in the form of abstract) in any journal or magazine for private or public circulation, and, is not under consideration of publication elsewhere.

·         I/We will not withdraw the manuscript after 1 week of submission as I have read the Author Guidelines and will adhere to the guidelines.

·         I/We Author(s ) have niether given nor will give this manuscript elsewhere for publishing after submitting in STM Journal(s).

·         I/ We have read the original version of the manuscript and am/ are responsible for the thought contents embodied in it. The work dealt in the manuscript is my/ our own, and my/ our individual contribution to this work is significant enough to qualify for authorship.

·          I/We also agree to the authorship of the article in the following order:

Author’s name                                    

 

1. ________________

2. ________________

3. ________________

4. _______________

 

We  Author(s) tick this box and would request you to consider it as our signature as we agree to the terms of this Copyright Notice, which will apply to this submission if and when it is published by this journal.